www.picengrave.com

PicSender 3.3.3

PicSender

The VERY basics of PicSender

This video was not made by us it was posted on youtube by Tim Miller,
but if your needing help figuring out how to use PicSender please check out
his video, he explains how to setup the program and machine.

Version 3.6.6 - Released January 2021

A new Gcode sender program written
specifically to stream image Gcode files to cnc
machines controlled by GRBL. Optimized for
use with Gcode files generated by PicLaser,
PicLaser Lite & PicEngrave Pro 6.

PicSender

$34.95 USD

(Download only)

Information About The Program

PicSender Features:

	• Streams large fast changing Raster & Vector Gcode files to GRBL.
	• Supports grbl .9, 1.0 & 1.1, Multi-Mode grbl 1.0c and grbl 1.1f
          EmBlaser's (aka LazerBlade) grbl 9g, 1.0c & 1.1f and J-Tech's LaserMode
          grbl .9g. Testing Recommended.
	• Displays position feedback responses from GRBL.
	• Selectable jog modes - Absolute (G90) or Incremental (G91).
	• Selectable jog move values.
	• Manual keyboard jog and USB Numeric Keypad pendant jog support.
	• Sets/resets G54 offset values.
	• Loads and streams Gcode files of up to 20 million lines
          in length, but limits depend on PC Memory & Windows version.
	• Display and set GRBL setup values.
	• Manual control of spindle/laser output signal.
	• Manual command option
	• Detects and reports Gcode format errors.
	• Elapsed Time and Estimated Run Time display.
	• Run time progress indicator.
	• Simple and easy-to-use controls.
	• Use with lasers or rotary spindles.
        • Ability to Zero/Set the X,Y & Z axis's in 4 independent positions.
        • Easy batch editing of GRBL settings.
        • Save settings to uniquely named files for later recall.
        • Load previously saved setting files.
        • Easily review all settings before uploading to GRBL.
        • Send settings to GRBL one at a time, or all at the same time.
        • Compare present and previous settings.
        • Limit Switch monitoring.
        • Set Safe Z retract distance for when a job is canceled.
        • Easy setting of up to 6 different Coordinate offsets.
        • Manual Move Control Menu.
        • Pause/Resume for Spindle & Laser.
        • Change Feed Rate During Gcode Streaming.
        • Gcode Editor.
        • Tool Position Setting Menu.
        • 45 Degree X&Y Jog Buttons Added.
        • QCode (QuickCode) menu added to send/run quick gcode routines. In v2.8.0+.
        • Minimum System Requirements: Windows XP SP3, Atom 1.6 Ghz
          processor and 1GB of Ram.
        • Recommended System Requirements. Windows 7-10, 2.8 Ghz Processor
          and 4GB or more of Ram.
        • Test the DEMO with your PC before purchase.

GRBL Firmware Downloads

MultiMode GRBL 1.0c | EmBlaser 1 GRBL 1.0c

Picsender Tutorial

Forum Page

Demo Download Table

Program Name	Program version	File Name
PicSender	3.6.6	PicSender3setup.zip

Note: The unlicensed demo version is limited by
only running half of the gcode file and batch editing/backup of grbl settings is disabled.

PLEASE NOTE: PicSender works only with those versions of MS Windows
that use points (.) for decimal separators (as does GRBL) - commas (,) are not supported.

Notice:

Please do not purchase any of our programs
until you have tested the demo version and you are
sure it works with your version of MS Windows and
your cnc operating system.

**********************************************************************

No refunds will be made after the
registration code has been emailed to you.

**********************************************************************

Notice:

Following purchase completion, a registration code will be sent to your email
address included with your payment information that will unlock the demo and remove
the restrictions from the program.

**********************************************************************

This program is sold as a download only - no disks are available.

**********************************************************************

Distributor quantity License discounts available.
E-Mail us through our "Contact" page for more information.

If your planning on starting a Crowd-Funding Campaign with
CNC Laser photo engraving included, Contact Us. Special large quantity discounts
available for Creators of Crowd-Funding Projects.

Please allow up to 24 hours for a license email.